收藏本站
MAX4208 Evaluation Kit
V REFIN/MODE = VDD x ?
? R3 + R4 ?
REFIN/MODE Operation Modes
The EV kit jumper JU1 configures the MAX4208 for direct
reference, buffered reference, or shutdown mode. The
reference voltage at REF sets the output voltage DC sig-
nal, OUT, when the differential input signal V IN+ - V IN-
equals zero. In direct-reference-mode operation, con-
nect a user reference voltage directly to the REF PCB
pad. In buffered-reference-mode operation, connect a
user reference voltage to the REFIN/MODE input PCB
pad or use the resistor-divider network R3 and R4 to
provide a reference voltage for REFIN/MODE, scaled
from VDD. The network is configured to scale the volt-
age at REFIN/MODE to one-half of VDD. Replace resis-
tors R3 and R4 to modify the voltage applied to
REFIN/MODE using the following equation:
? R4 ?
?
where VDD is the input supply voltage to the EV kit.
REF Input
The EV kit’s jumper JU3 must be configured properly
for appropriate reference-voltage operation. In direct
reference mode, install a shunt on jumper JU3 to con-
nect REF to the on-board ground (GND), or remove the
shunt to connect a user reference voltage to the REF
input PCB pad. For either buffered-reference mode,
REF must not be connected to a reference voltage;
thus, the shunt on jumper JU3 must not be installed.
See Table 2 for jumper JU3 configurations.
Optional capacitor C6 can be used for reference-volt-
age stability/filtering. Choose an appropriate value as
needed.
On-Board Current Sensing
The MAX4208 EV kit can be configured for on-board
current sensing by installing a surface-mount 1206
sense resistor at R7, located between the IN+ and IN-
PCB pads. Use the following equation to select the
value for resistor R7:
In buffered-reference mode, the MAX4208 internally
buffers the REFIN/MODE voltage onto REF.
R7 =
30mV
I IN
Note: Do not connect an external source to the REF PCB
pad in buffered-reference mode. See Table 2 for jumper
JU1 configurations.
where I IN is the maximum current flowing across resis-
tor R7 and 30mV is a suggested sense voltage. 30mV x
148V/V gives a 4.4V output swing. Refer to the
Table 2. Jumpers JU1 and JU3 Configurations
MODE
JU1 SHUNT
POSITION
REFIN/MODE
PIN
JU3 SHUNT
POSITION
REF PIN
EV KIT FUNCTION
Installed
Connected to
GND
JU1 disables the internal REF buffer.
JU3 sets the REF voltage to GND.
Direct-reference-mode
operation
1-2
Connected to
VSS
Not installed
Connected to
user reference
JU1 disables the internal REF buffer.
JU3 allows the user to set the REF
voltage directly. Apply a user reference
voltage
voltage to the REF PCB pad in the 0V
and VDD - 1.6V range.
Shutdown mode
Buffered-reference-
mode operation
(on-board reference)
1-3
1-4
Connected to
VDD
Connected to
VDD / 2
—
Not installed
—
Not connected
Entire IC is in shutdown. I CC < 5μA.
The IC buffers the on-board VDD / 2
onto REF. Do not install JU3 or connect
an external source to the REF PCB pad.
The IC buffers a user reference voltage
Buffered-reference-
mode operation (user
reference)
Not installed
Connected to
user reference
voltage
Not installed
Not connected
onto REF. Apply a user reference
voltage to the REFIN/MODE PCB pad in
the range of VSS + 200mV and VDD -
1.6V. Do not install JU3 or connect an
external source to the REF PCB pad.
_______________________________________________________________________________________
3
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MAX4209EVKIT+ KIT EVAL FOR MAX4209
MAX4210EEVKIT EVAL KIT FOR MAX4210
MAX4273EVKIT EVAL KIT FOR MAX4273
MAX4278EVKIT-SO KIT EVALUATION FOR MAX4178,4278
MAX44265EVKIT# KIT EVAL FOR 44265
MAX4754AEVKIT+ KIT EVAL FOR MAX4754
MAX4810EVKIT+ KIT EVAL FOR MAX4810
MAX4886EVKIT+ KIT EVAL FOR MAX4886
相关代理商/技术参数
MAX4209EVKIT+ 功能描述:放大器 IC 开发工具 MAX4209 Eval Kit RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V
MAX4209HAUA+ 功能描述:仪表放大器 Low Offset/Drift Instrumentation Amp RoHS:否 制造商:Texas Instruments 通道数量: 输入补偿电压:150 V 可用增益调整: 最大输入电阻:10 kOhms 共模抑制比（最小值）:88 dB 工作电源电压:2.7 V to 36 V 电源电流:200 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:MSOP-8 封装:Bulk
MAX4209HAUA+T 功能描述:仪表放大器 Low Offset/Drift Instrumentation Amp RoHS:否 制造商:Texas Instruments 通道数量: 输入补偿电压:150 V 可用增益调整: 最大输入电阻:10 kOhms 共模抑制比（最小值）:88 dB 工作电源电压:2.7 V to 36 V 电源电流:200 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:MSOP-8 封装:Bulk
MAX420C/D 功能描述:运算放大器 - 运放 RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel
MAX420CPA 功能描述:运算放大器 - 运放 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel
MAX420CPA+ 功能描述:运算放大器 - 运放 Chopper Stabilized RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel
MAX420CPA-101 制造商:Maxim Integrated Products 功能描述:
MAX420CTV 功能描述:运算放大器 - 运放 RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel